Page All:
Page 1
Broadcom Announces Industry's Lowest Power Dual/Quad CDRs for High Density 10G Applications
New Low Power & Latency CDRs Provide Improved Signal Integrity with Referenceless Operation
LOS ANGELES, March 7, 2011/PRNewswire/ -- OFC/NFOEC 2011 -- Broadcom Corporation (Nasdaq: BRCM), a global leader in semiconductors for wired and wireless communications, today announced the addition of three new 10GbE clock and data recovery (CDR) devices to its high-speed interconnect products (HSIP) portfolio that provide increased signal integrity while achieving the lowest power consumption in the industry. Broadcom will demonstrate these new CDR solutions for wired networking at this week's Optical Fiber Communication (OFC) Conference and Exposition, March 8-10, 2011 at the Los Angeles Convention Center, Booth #1557.
The Broadcom® BCM8322, BCM8324 and BCM8325 are low power, low latency (referenceless) dual and quad CDRs with integrated limiting amplifiers, ideal for high port count 10 Gigabit Ethernet (10GbE) applications while providing support re-timing for 8GbE fiber channel, OC-192, 10GbE and OTU-2(e) rates. The new devices reset the jitter budget and enable longer printed circuit board (PCB) traces, compensating for transmission losses thereby increasing system signal integrity.
Highlights/Key Facts
-- Signal integrity is an issue that must be addressed by PCB designers in
order to achieve the target bit error rate (BER), especially with long
traces between the switch (or framer ASIC) and the optical module on the
front panel. With the growing proliferation of 10GbE connectivity, port
count densities will increase with the use of SFP+ modules on
line-cards.
-- The high level of integration and low power of the dual CDR BCM8322 will
enable the next generation of XFP modules and a new generation of
re-timed SFP+ modules.
-- Industry's lowest power consumption at approximately 125mW and each CDR
can be individually powered down.
-- Enables sub-1W SFP+ modules that are SONET compliant.
-- The referenceless CDR solutions operate over a wide data range from
8.5Gbps to 11.4Gbps without the need for an input reference clock.
-- The quad CDR BCM8324 and BCM8325 devices serve an important function in
resolving signal integrity problems due to board layout on high
density/multi-port 10GbE line-cards. Key features of the CDRs include
the following:
-- Broadcom EyeOpener® technology, limiting amplifier and loss of
signal detection.
-- Incorporates programmable Tx pre-emphasis on the transmit outputs
and programmable Rx equalization on the receive inputs.
-- The combined Tx pre-emphasis and Rx equalization improve the
overall reach and compensate for electrical imperfections
associated with line traces and connectors on high port count
line-cards.
-- Complies with Optical Internetworking Forum (OIF), IEEE 802.3ae,
Telcordia®, ANSI, and ITU-T jitter standards.
-- Pin compatible with previous generation BCM8302/8304/8305 CDR solutions.
-- The Broadcom BCM8322 is a fully integrated multirate CDR that operates
from 8.5 Gigabits per second (Gbps) to 11.4 Gbps and is targeted to
small form factors such as XFP module applications and SFP+ line-card
applications.
-- The Broadcom BCM8324 is a fully integrated multi-rate CDR that operates
from 8.5 Gigabits per second (Gbps) to 11.4 Gbps and is targeted to
40GbE modules, 4x10 Gigabit (10G) applications and for retiming 10G
signals on line-cards for SFI/XFI compliance.
-- The Broadcom BCM8325 is a fully integrated quad CDR that operates at
10.3125 Gbps and is targeted for 10GbE/40GbE modules, and for retiming
10GbE signals on line-cards.
-- All devices are now sampling to early access customers with volume
production in the second half of 2011.
Quotes:
Lorenzo Longo, Vice President & General Manager, High-Speed Interconnect Products (HSIP)
Broadcom Corporation
"Design teams focused on enabling the new generation of 10G applications need better solutions to take advantage of this proliferating technology. Broadcom's high-speed interconnect products are proven in the market and our new CDR offerings provide a reference-less design that delivers the industry's lowest power consumption and latency of less than 1 ns, while solving the signal integrity problems on high density line-cards."
Andrew Schmitt, Directing Analyst, Infonetics Research Inc.
"Ethernet convergence in the service provider and data center segments is driving 10GbE port growth while 10GbE traffic growth is driving 40GbE demand in optical transport applications. Broadcom's new family of CDR solutions provides an opportunity to increase their SAM in this fast growing market."
Subscribe to RSS Feed:
Broadcom Infrastructure & Networking Group
http://go.broadcom.com/sv2
Resources:
Featured Product Page
About Broadcom
Broadcom Corporation is a prominent technology innovator and global leader in semiconductors for wired and wireless communications. Broadcom products enable the delivery of voice, video, data and multimedia to and throughout the home, the office and the mobile environment. We provide the industry's broadest portfolio of state-of-the-art system-on-a-chip and embedded software solutions to manufacturers of computing and networking equipment, digital entertainment and broadband access products, and mobile devices. These solutions support our core mission: Connecting everything®.
Broadcom, one of the world's largest fabless communications semiconductor companies, with 2010 revenue of $6.82 billion, holds more than 4,800 U.S. and 2,000 foreign patents, and has more than 7,800 additional pending patent applications, and one of the broadest intellectual property portfolios addressing both wired and wireless transmission of voice, video, data and multimedia.
A FORTUNE 500® company, Broadcom is headquartered in Irvine, Calif., and has offices and research facilities in North America, Asia and Europe. Broadcom may be contacted at +1.949.926.5000 or at http://www.broadcom.com.
Cautions regarding Forward-Looking Statements:
All statements included or incorporated by reference in this release, other than statements or characterizations of historical fact, are forward-looking statements. These forward-looking statements are based on our current expectations, estimates and projections about our industry and business, management's beliefs, and certain assumptions made by us, all of which are subject to change. Forward-looking statements can often be identified by words such as "anticipates," "expects," "intends," "plans," "predicts," "believes," "seeks," "estimates," "may," "will," "should," "would," "could," "potential," "continue," "ongoing," similar expressions, and variations or negatives of these words. Examples of such forward-looking statements include, but are not limited to, the demand for 10GbE CDR solutions, our position in that space, and the timing of volume production for the BCM8322, BCM8324 and BCM8325 CDR solutions. These forward-looking statements are not guarantees of future results and are subject to risks, uncertainties and assumptions that could cause our actual results to differ materially and adversely from those expressed in any forward-looking statement.
Important factors that may cause such a difference for Broadcom in connection with the BCM8322, BCM8324 and BCM8325 CDR solutions include, but are not limited to:
-- The rate at which our present and future customers and end-users adopt
Broadcom's technologies and products;
-- The timing, rescheduling or cancellation of significant customer orders
and our ability, as well as the ability of our customers, to manage
inventory; and
-- Competitive pressures and other factors such as the qualification,
availability and pricing of competing products and technologies and the
resulting effects on sales and pricing of our products.
Additional factors that may cause Broadcom's actual results to differ materially from those expressed in forward-looking statements include, but are not limited to the list that can be found at http://www.broadcom.com/press/additional_risk_factors/Q12011.php.
Our Annual Report on Form 10-K, subsequent Quarterly Reports on Form 10-Q, recent Current Reports on Form 8-K, and other Securities and Exchange Commission filings discuss the foregoing risks as well as other important risk factors that could contribute to such differences or otherwise affect our business, results of operations and financial condition. The forward-looking statements in this release speak only as of this date. We undertake no obligation to revise or update publicly any forward-looking statement, except as required by law.
Broadcom®, the pulse logo, Connecting everything®, the Connecting everything logo and EyeOpener® are among the trademarks of Broadcom Corporation and/or its affiliates in the United States, certain other countries and/or the EU. Any other trademarks or trade names mentioned are the property of their respective owners.
Contacts
Trade Press Investor Relations
Tamara Snowden Chris Zegarelli
Senior Manager, Corporate Communications Director, Investor Relations
408-922-6505 949-926-7567
tamaras@broadcom.com czegarel@broadcom.com
SOURCE Broadcom Corporation; BRCM Infrastructure & Networking
Photo:http://photos.prnewswire.com/prnh/20060609/BROADCOMLOGO
http://photoarchive.ap.org/
Broadcom Corporation; BRCM Infrastructure & Networking
CONTACT: Trade Press, Tamara Snowden, Senior Manager, Corporate Communications, +1-408-922-6505, tamaras@broadcom.com, or Investor Relations, Chris Zegarelli, Director, Investor Relations, +1-949-926-7567, czegarel@broadcom.com
Web Site: http://www.broadcom.com
Broadcom Announces Industry's Lowest Power Dual/Quad CDRs for High Density 10G Applications
New Low Power & Latency CDRs Provide Improved Signal Integrity with Referenceless Operation
LOS ANGELES, March 7, 2011/PRNewswire/ -- OFC/NFOEC 2011 -- Broadcom Corporation (Nasdaq: BRCM), a global leader in semiconductors for wired and wireless communications, today announced the addition of three new 10GbE clock and data recovery (CDR) devices to its high-speed interconnect products (HSIP) portfolio that provide increased signal integrity while achieving the lowest power consumption in the industry. Broadcom will demonstrate these new CDR solutions for wired networking at this week's Optical Fiber Communication (OFC) Conference and Exposition, March 8-10, 2011 at the Los Angeles Convention Center, Booth #1557.
The Broadcom® BCM8322, BCM8324 and BCM8325 are low power, low latency (referenceless) dual and quad CDRs with integrated limiting amplifiers, ideal for high port count 10 Gigabit Ethernet (10GbE) applications while providing support re-timing for 8GbE fiber channel, OC-192, 10GbE and OTU-2(e) rates. The new devices reset the jitter budget and enable longer printed circuit board (PCB) traces, compensating for transmission losses thereby increasing system signal integrity.
Highlights/Key Facts
-- Signal integrity is an issue that must be addressed by PCB designers in
order to achieve the target bit error rate (BER), especially with long
traces between the switch (or framer ASIC) and the optical module on the
front panel. With the growing proliferation of 10GbE connectivity, port
count densities will increase with the use of SFP+ modules on
line-cards.
-- The high level of integration and low power of the dual CDR BCM8322 will
enable the next generation of XFP modules and a new generation of
re-timed SFP+ modules.
-- Industry's lowest power consumption at approximately 125mW and each CDR
can be individually powered down.
-- Enables sub-1W SFP+ modules that are SONET compliant.
-- The referenceless CDR solutions operate over a wide data range from
8.5Gbps to 11.4Gbps without the need for an input reference clock.
-- The quad CDR BCM8324 and BCM8325 devices serve an important function in
resolving signal integrity problems due to board layout on high
density/multi-port 10GbE line-cards. Key features of the CDRs include
the following:
-- Broadcom EyeOpener® technology, limiting amplifier and loss of
signal detection.
-- Incorporates programmable Tx pre-emphasis on the transmit outputs
and programmable Rx equalization on the receive inputs.
-- The combined Tx pre-emphasis and Rx equalization improve the
overall reach and compensate for electrical imperfections
associated with line traces and connectors on high port count
line-cards.
-- Complies with Optical Internetworking Forum (OIF), IEEE 802.3ae,
Telcordia®, ANSI, and ITU-T jitter standards.
-- Pin compatible with previous generation BCM8302/8304/8305 CDR solutions.
-- The Broadcom BCM8322 is a fully integrated multirate CDR that operates
from 8.5 Gigabits per second (Gbps) to 11.4 Gbps and is targeted to
small form factors such as XFP module applications and SFP+ line-card
applications.
-- The Broadcom BCM8324 is a fully integrated multi-rate CDR that operates
from 8.5 Gigabits per second (Gbps) to 11.4 Gbps and is targeted to
40GbE modules, 4x10 Gigabit (10G) applications and for retiming 10G
signals on line-cards for SFI/XFI compliance.
-- The Broadcom BCM8325 is a fully integrated quad CDR that operates at
10.3125 Gbps and is targeted for 10GbE/40GbE modules, and for retiming
10GbE signals on line-cards.
-- All devices are now sampling to early access customers with volume
production in the second half of 2011.
Quotes:
Lorenzo Longo, Vice President & General Manager, High-Speed Interconnect Products (HSIP)
Broadcom Corporation
"Design teams focused on enabling the new generation of 10G applications need better solutions to take advantage of this proliferating technology. Broadcom's high-speed interconnect products are proven in the market and our new CDR offerings provide a reference-less design that delivers the industry's lowest power consumption and latency of less than 1 ns, while solving the signal integrity problems on high density line-cards."
Andrew Schmitt, Directing Analyst, Infonetics Research Inc.
"Ethernet convergence in the service provider and data center segments is driving 10GbE port growth while 10GbE traffic growth is driving 40GbE demand in optical transport applications. Broadcom's new family of CDR solutions provides an opportunity to increase their SAM in this fast growing market."
Subscribe to RSS Feed:
Broadcom Infrastructure & Networking Group
http://go.broadcom.com/sv2
Resources:
Featured Product Page
About Broadcom
Broadcom Corporation is a prominent technology innovator and global leader in semiconductors for wired and wireless communications. Broadcom products enable the delivery of voice, video, data and multimedia to and throughout the home, the office and the mobile environment. We provide the industry's broadest portfolio of state-of-the-art system-on-a-chip and embedded software solutions to manufacturers of computing and networking equipment, digital entertainment and broadband access products, and mobile devices. These solutions support our core mission: Connecting everything®.
Broadcom, one of the world's largest fabless communications semiconductor companies, with 2010 revenue of $6.82 billion, holds more than 4,800 U.S. and 2,000 foreign patents, and has more than 7,800 additional pending patent applications, and one of the broadest intellectual property portfolios addressing both wired and wireless transmission of voice, video, data and multimedia.
A FORTUNE 500® company, Broadcom is headquartered in Irvine, Calif., and has offices and research facilities in North America, Asia and Europe. Broadcom may be contacted at +1.949.926.5000 or at http://www.broadcom.com.
Cautions regarding Forward-Looking Statements:
All statements included or incorporated by reference in this release, other than statements or characterizations of historical fact, are forward-looking statements. These forward-looking statements are based on our current expectations, estimates and projections about our industry and business, management's beliefs, and certain assumptions made by us, all of which are subject to change. Forward-looking statements can often be identified by words such as "anticipates," "expects," "intends," "plans," "predicts," "believes," "seeks," "estimates," "may," "will," "should," "would," "could," "potential," "continue," "ongoing," similar expressions, and variations or negatives of these words. Examples of such forward-looking statements include, but are not limited to, the demand for 10GbE CDR solutions, our position in that space, and the timing of volume production for the BCM8322, BCM8324 and BCM8325 CDR solutions. These forward-looking statements are not guarantees of future results and are subject to risks, uncertainties and assumptions that could cause our actual results to differ materially and adversely from those expressed in any forward-looking statement.
Important factors that may cause such a difference for Broadcom in connection with the BCM8322, BCM8324 and BCM8325 CDR solutions include, but are not limited to:
-- The rate at which our present and future customers and end-users adopt
Broadcom's technologies and products;
-- The timing, rescheduling or cancellation of significant customer orders
and our ability, as well as the ability of our customers, to manage
inventory; and
-- Competitive pressures and other factors such as the qualification,
availability and pricing of competing products and technologies and the
resulting effects on sales and pricing of our products.
Additional factors that may cause Broadcom's actual results to differ materially from those expressed in forward-looking statements include, but are not limited to the list that can be found at http://www.broadcom.com/press/additional_risk_factors/Q12011.php.
Our Annual Report on Form 10-K, subsequent Quarterly Reports on Form 10-Q, recent Current Reports on Form 8-K, and other Securities and Exchange Commission filings discuss the foregoing risks as well as other important risk factors that could contribute to such differences or otherwise affect our business, results of operations and financial condition. The forward-looking statements in this release speak only as of this date. We undertake no obligation to revise or update publicly any forward-looking statement, except as required by law.
Broadcom®, the pulse logo, Connecting everything®, the Connecting everything logo and EyeOpener® are among the trademarks of Broadcom Corporation and/or its affiliates in the United States, certain other countries and/or the EU. Any other trademarks or trade names mentioned are the property of their respective owners.
Contacts
Trade Press Investor Relations
Tamara Snowden Chris Zegarelli
Senior Manager, Corporate Communications Director, Investor Relations
408-922-6505 949-926-7567
tamaras@broadcom.com czegarel@broadcom.com
SOURCE Broadcom Corporation; BRCM Infrastructure & Networking
Photo:http://photos.prnewswire.com/prnh/20060609/BROADCOMLOGO
http://photoarchive.ap.org/
Broadcom Corporation; BRCM Infrastructure & Networking
CONTACT: Trade Press, Tamara Snowden, Senior Manager, Corporate Communications, +1-408-922-6505, tamaras@broadcom.com, or Investor Relations, Chris Zegarelli, Director, Investor Relations, +1-949-926-7567, czegarel@broadcom.com
Web Site: http://www.broadcom.com